Elemento calentador de cartucho de cabezal único, tubo de calentamiento de resistencia de alta densidad para molde, troquel
The heating part of the core of the cartridge heater is a nickel-chromium heat-resistant alloy wire, que está enrollado en una varilla con núcleo de óxido de magnesio con excelente aislamiento y conductividad térmica.. El cable calefactor y la carcasa están llenos de polvo de óxido de magnesio como material aislante., Y el aire del interior es comprimido por la máquina para convertirlo en un todo..
After the main body of the cartridge heater is completed, La pieza de fijación o rosca se puede instalar según las necesidades de instalación.. La estructura roscada de la pieza de fijación está relacionada con el método de instalación del tubo calefactor.. Póngase en contacto con nuestro personal técnico o de ventas para obtener la mejor solución..
Debido a las diversas formas y especificaciones, es imposible mostrarlos todos. If you need to customize various special-shaped heating tubes, por favor contacte con el servicio al cliente.
Parámetros del producto
1.Diameter 2.Volts and watts 3.Length 4.Type of lead wire 5.Select the outlet method
Main material
Heating wire Ni8Cr20 nickel chromium wire
Insulation filling High purity magnesium oxide powder
Shell (protection tube) SS304,SS310S,SS316,TA1,Incoloy800(NCF800)
Lead Silicone glass fiber (temperature resistance 250ºC)
teflón (temperature resistance 250ºC)
High temperature glass fiber (temperature resistance 400ºCCeramic beads (temperature resistant to 800ºC)
Lead protection Silicone fiberglass casing, metal braided hose, metal corrugated hose
Sealed end (caza de focas) Ceramic/ceramic glue (temperature resistant 800ºC)
caucho de silicona (temperature resistant 180ºC)
Resin (temperature resistance 250ºC)
Referencia de tamaño de diámetro estándar
Diameter in millimeters (milímetros): 2, 3, 4, 5, 6, 6.5, 8, 9.5, 10, 12, 12.5, 14, 15, 15.8, 16, 18, 19, 20, 25, 30, etc..
Diameter inches (pulgada): 1/4″, 3/8″, 1/2″, 5/8″, 3/4″, 1″, etc.. (Observaciones: 1 pulgada = 25.4 milímetros)
Nota: High-power heating tubes are used in the mold, y los orificios de montaje deben reservarse en el molde de acuerdo con el tamaño del calentador de cartucho (or the outer diameter of the heating tube can be customized according to the size of the mounting hole). Please minimize the size of the heating tube and the mounting hole. Clearance. When machining mounting holes, the unilateral clearance is recommended to be within 0.05mm.
Nota: The slash area in the figure represents the heating section of the heating tube
Nota: Personalice la profundidad del orificio del molde según la longitud de la parte calefactora del calentador de cartucho
Si el agujero es demasiado profundo, the heating part of the heating tube will be exposed after installation, and there is no good heat dissipation environment, which will damage the heating tube and may even cause accidents such as fire.
Si el agujero es demasiado profundo, the heating tube will be sealed after installation, and the lead part will fall into a higher use environment. Long-term use may cause problems such as a short circuit between the electrodes.
Nota: El tubo calefactor debe protegerse de la humedad.. Se recomienda comenzar con un voltaje bajo durante el uso inicial..
Storage and use in a high-humidity environment will cause the insulation resistance to drop, but after the power is turned on, the moisture in the heating tube will evaporate and the insulation performance will gradually recover. It is recommended to start with a low voltage.
Product laboratory
The mold cartridge heater is a product developed by Super electric heating technology and has undergone many trials and tests.
Each new product developed by Super Electric Heating Technology Company will be tested in our professional laboratory in all aspects of performance, especially the function completion and thermal stability under load conditions.
After the new product is tested, the experimental data is generated. Our engineers analyze the data and then feed the results back to the engineering staff for product optimization to ensure that customers get the product that best meets their expectations.
HOT CORE Heating Technology Co., Limitado. has been specializing in the production of high-density hot bar resistance heating tubes for molds and dies since 1985.which is well-known as one of the leading manufacturers and suppliers of high density hot rod resistance heating tube single head cartridge heater element for mould die. En los últimos años, Teníamos una sólida reputación por la alta calidad., Rendimiento confiable y gran durabilidad de nuestros productos.. ¿Deberías estar interesado?, no dude en ponerse en contacto con nuestra fábrica. Etiquetas calientes: high density hot rod resistance heating tube single head cartridge heater element for mould die manufacturers, proveedores, fábrica
