Proveedores de Cartuchos de calentador
Hot Core Heater Specializing in the production of various types of precision tubular heater for vacuum plating, niquelado, chapado en oro, chapado en plata, cromado y otros equipos de revestimiento al vacío. El calentador tubular de galvanoplastia al vacío tiene varias formas., resistencia a altas temperaturas, resistencia al desgaste, larga vida útil, alta eficiencia de conducción, y la carcasa está hecha de tubo sin costura de alto rendimiento, que es ampliamente utilizado en la industria del vacío.
Descripción de productos
1) The heating part of the core of the Superb Heater cartridge heater is a nickel-chromium heat-resistant alloy wire, which is wound on a magnesium oxide core rod with excellent insulation and thermal conductivity. The heating wire and the shell are filled with magnesium oxide powder as an insulating material, and the air inside is compressed by the machine to make it into a whole.
2) After the main body of the cartridge heater is completed, the fixing piece or thread can be installed according to the installation needs. The thread structure of the fixing piece is related to the heating tube installation method. Please contact our sales or technical personnel for the best solution.
Due to the various shapes and specifications, it is impossible to display all of them.
If you need to customize special-shaped of cartridge heater, please contact customer service!
Model NO. Cartridge heater
Insulation Material High-Purity MGO Powder
Tolerancia a la potencia +/-10%
Voltage Customize
Internal Thermocouple Type J or K
Warranty one year
Note: The “slash area” in the figure represents the heating section of the superb heater heating tube
1) Note: Customize the hole depth of the mold according to the length of the heating part of the cartridge heater
—If the hole is too shallow, the heating part of the cartridge heater will be exposed after installation, and there is without good heat dissipation environment, which will damage the cartridge heater and and even may cause fire and other accidents.
—If the hole is too deep, the sealing and wire part of the cartridge heater after installation will fall into a more severe use environment. Long-term use may lead to short circuit between electrodes and other problems.
2) Note: The heating tube should be protected from moisture. It is recommended to start with a low voltage during initial use.
—The cartridge heater should be moisture-proof, and it is recommended to use lower voltage for initial use.
When the superb heater cartridge heater is stored and used in a high humidity environment, the insulation resistance will decrease. but after the cartridge heater is powered on, the moisture will evaporate, and the insulation performance will gradually recover. It is recommended to start the cartridge heater with lower voltage.
Standard diameter size reference
1) DiameterΦ in mm: 2, 3, 4, 5, 6, 6.5, 8, 9.5, 10, 12, 12.5, 14, 15, 15.8, 16, 18, 19, 20, 25, 30, etc..
2) DiameterΦ inch: 1/4″, 3/8″, 1/2″, 5/8″, 3/4″, 1″, etc.. (Remarks: 1 inch = 25.4 milímetros)
3) Note: High-power cartridge heater are used in the mold heating, and mounting holes need to be reserved on the mold according to the size of the cartridge heater (or the outer diameter of the cartridge heater can be customized according to the size of the mounting hole).Superb Heater suggest Minimize the gap between the cartridge heater and the mounting hole. When machining the mounting hole, it is recommended that the gap on one side be less than 0.05mm.
What is the difference between terminal type and inner lead?
From the figure above, we can clearly see the difference between the terminal type and the inner lead structure.
1) The terminal type is the lead rod and the lead wire are connected outside the cartridge heater through the crimping terminal.
2) The inner lead is the lead wire is directly connected from the inside of the cartridge heater.
The terminal type usually uses the glass fiber sleeve to wrap the wiring, 1. to increase the insulation protection, 2. to protect this part of the lead to avoid excessive bending
¿Por qué elegirnos??
☆Ventas directas de fábrica, Las especificaciones y tamaños se pueden personalizar según los dibujos..
△Producimos elementos calefactores de diversos materiales.(PTFE,De,Acero inoxidable 304/316L/310S,etc.), según los clientes’ requisitos.
△Múltiples tamaños y formas , y el vatio & El voltaje se puede personalizar.
☆ Los productos utilizan materias primas de alta calidad para garantizar la calidad del producto..
☆ Apoye el servicio postventa profesional para resolver a los clientes.’ preocupaciones.
☆We will check the quantity and inspect the goods before deliver.
